A robot axis and a cabinet entry can sit only a few metres apart on the same machine, yet their conduit duties are different. At the cabinet, the bend may happen once during assembly. At the axis, it happens through the work cycle. For machine wiring, separate three wall constructions first: interlocked metal, metal under a polymer jacket, and corrugated plastic. Then ask whether the route moves. That second question can change the specification more than the material label.
Read a conduit name as a clue to its layers, not a full cross-section. Stainless steel can identify the metal core; PE can name a plastic tube or the cover over metal. That distinction affects which fitting can grip the product and which limits apply, so check the layer description before choosing the termination.
The comparison below is about industrial product construction, not code classification. If a project drawing calls for a listed conduit type, verify the exact model and installation against that requirement; a family name alone cannot establish it.
Conduit family | Construction | Question for machine wiring |
Bare flexible metal | Interlocked metal strip | Does the exposed metal suit the location? |
Jacketed flexible metal | Metal core with a polymer covering | What can the jacket and termination withstand? |
Corrugated plastic | Profiled PA, PE or PP wall | Is the exact grade intended for this route? |
Conduit for repeated motion | Application-specific flexible construction | What bending and movement conditions were tested? |
The last row overlaps the others. Motion capability is a further requirement applied to a construction, rather than a separate material. A fixed cabinet connection and a robot wrist can need very different products even when their conduit walls use the same polymer.

Metal flexible conduit in this family uses an interlocked strip for its bendable wall. LEINUOER lists galvanized steel and stainless steel versions. When routing between a cabinet and a machine frame, trace the required offset and select a size and connector made for that conduit construction.
At a machine tool, inspect the entire entry where a line reaches the coolant zone: conduit surface, end fitting and enclosure interface. Calling the tube metal does not establish that this joint excludes fluid. The assembly needs documented protection for the actual exposure.
A grade name is only one input to corrosion selection. The listed range includes 304 and 316 stainless steel conduit; if the route meets a cleaning solution, state the solution and operating conditions when checking the specific product. Do not treat the grade number alone as a compatibility decision.
The jacket meets the machine environment before the metal core does. LEINUOER's range includes PVC-, TPU- and PE-covered constructions, so a heated drive or wash area makes the outer-layer specification relevant. Select against the conditions stated for the particular model, not a rating borrowed from another covering.
Model LNE-JSBH-PE has a 304 stainless steel strip inner layer and a corrugated PE outer layer. Its working range is −10°C to +80°C. Those limits belong to this model; they should not be applied to every PE-covered tube or every stainless steel conduit.
A drawing that says only “stainless steel conduit” would leave out a decisive part of that example. Name the jacket as well, then compare the actual machine exposure with the model's stated working range. The steel core and the PE cover answer different specification questions.

LEINUOER's electrical plastic flexible conduit range lists PA, PA12, PE and PP products, including separate flame-retardant variants. That product split matters when a drawing calls for a grade or a fire classification: “PA conduit” alone does not identify which version to install. Name the exact product specification required by the project.
On a fixed automation frame, corrugations let a tube route around brackets before entering an enclosure. The bend during installation is only one part of the choice: check the selected grade against the machine's environment and the fitting made for that wall profile.
A moving axis changes the duty from one installation bend to repeated travel. Before choosing a tube for a robot or reciprocating carriage, identify its installed bend radius, stroke, cycle pattern and any twist. Then confirm that the specific conduit construction is supported for those conditions; the word “flexible” alone does not say it is.
Split double-layer corrugated conduit is another construction option. Its split form can help where protection must be placed around existing wiring. The closure and any joints still need assessment for the route; the split construction alone is not evidence of a watertight assembly.

A connector must match the enclosure at one end and the conduit at the other. Specify flexible metal conduit connectors for the selected metal construction and size; for plastic, use a fitting shaped for that tube's corrugation. The same thread at the enclosure cannot compensate for the wrong conduit-side grip.
A wet route makes this especially relevant. The jacket, connector seal and enclosure entry work together, so a protection claim for one component cannot establish the performance of the finished assembly. Check the documented combination and installation conditions before putting an ingress rating on the machine drawing.
A useful drawing note gives the wall construction, any jacket or polymer grade, the route's exposure, and whether it moves; the connector follows from those choices. A cabinet entry in a dry enclosure and a robot wrist may both use flexible tube, but their service duties are different.
No. PE can form the full tube wall or serve as a cover over metal. On LNE-JSBH-PE, the inner layer is 304 stainless steel strip and the outer layer is corrugated PE.
Flexibility during installation does not establish repeated-motion performance. A robot route needs evidence applicable to its bending, travel and torsion, including the way the conduit is supported.
No. The thread describes the enclosure side. You still need a connector whose other end is made for the conduit's construction and size; otherwise the enclosure may accept the fitting while the tube does not.
No. PA names the polymer family, while standard and flame-retardant are separate product variants. Check the exact grade against the classification required for your installation.
A replacement must match the service as well as the dimensions: wall construction, jacket or grade, exposure, movement and fitting. If the route now crosses a wash zone or moves with an axis, update the note before choosing a tube that only looks like the original.

Scan and consult WhatsApp customer service